Biscuit Timer Programming

From Jack's Wiki

Biscuit Timer

1 – Bake 10 minutes
2 – Bake 10 minutes
3 – Reheat 4 minutes
4 – Reheat 4 minutes
5 – Biscuit Bites 7 minutes
6 – Biscuit Bites 7 minutes
7 – Finish 1 minute
8 – Green Beans 10 minutes

(20 minute cook time)

Alignment

  • Channels 1 and 2 are used when baking biscuits
  • Total cooking time will be 10 minutes
  • Channels 3 and 4 will be used when reheating biscuits
  • Total re-heating or cook time will be 4 minutes
  • Channel 5 and 6 will be used when baking biscuit bites
  • Total cook time is 7 minutes
  • Channel 7 is used to finish cooking biscuits that have not reached the correct color after 8 minutes
  • Total finish time is 1 minute
  • Channel 8 is used when cooking green beans
  • Total cook time is 20 minutes

Programming Biscuit Timer - Roundup

1.     To program, press and hold the channel number you want to program. Hold for three seconds. The letters PGM will appear in the display area above the channel number you selected.  This means that the timer is in PROGRAM MODE. 

2.      A TIME STAGE NAME will flash in the TIME STAGE AREA. Use the up and down arrows to choose STAGE ONE, then press ENTER.

3.      The TIME DISPLAY will show the selected TIME STAGE NAME. Use the up and down buttons to set the desired time to 0 hours, then press the ENTER button. After that, set your desired time to 26 minutes and 0 seconds.  Press ENTER after each entry. TO CLEAR THE TIME TO 00:00:00, PRESS AND RELEASE THE UP AND DOWN ARROWS TOGETHER.

4.     Follow the same procedures to set CHANNEL 2 – 8.

IMPORTANT: The timer will exit the program mode in 10 seconds if a button is not pressed.

When finished, wait 10 seconds for the timer to exit programming mode.

5.     Press, then release CHANNEL 1.  The timer will start to countdown.

6.     All of the channels can be timing at the same time.  The timer will display the time for the channel you last selected.

7.     The timer will sound twice per second for two minutes, until the channel button is pressed.

8.      When one timing cycle is finished and the channel button is pressed, the display will show the next channel to finish.

IMPORTANT: Do not block the Solar Cells located at the top and front of the timer.  If these cells are blocked the timer will not function properly.

Programming Biscuit Timer - Prince Castle

1. To program, press and hold the PRINCE CASTLE LOGO for eight seconds. A beep will sound and the CHANNEL/FUNCTION DISPLAY will read SEL CH / LOGO = QUIT.

2. Select and press TIMER 1. The LED indicator for timer 1 will turn yellow and a beep will sound. The CHANNEL/FUNCTION display will read, CKT=COOK TIME with up and down arrows. The current complete cook time for that channel will be displayed in the TIME display, and the time value will indicate either H:M OR M:S (HOURS & MINUTES – MINUTES & SECONDS)

3. Using the SCAN/UP Arrow or the SCAN/DOWN Arrow buttons, set the time at 6:00 minutes. Press the ENTER button to store the complete cook time. Note: The Enter button must be pressed after any time changes in the cook; duty or hold functions or the time change will not be stored.

IMPORTANT: To change from Minutes and Seconds M:S to Hours and Minutes H:M. Press and hold the SCAN/UP Button. When the display reaches 59:59 it will automatically change to 1:00 hour and the LED will switch from M:S to H:M. The program value for the H:M indicator is from 1:00 hour to 17 hours: 59 minutes.

4. Once you press ENTER, The CHANNEL/FUNCTION display switches to CKC=MAN CANCEL, this allows you to select a manual or an automatic alarm cancel, press the SCAN UP arrow or SCAN DOWN arrow to toggle between AUT and MAN Cancel. Press the ENTER button to store your selection.

IMPORTANT: Always select manual cancel. This will require someone to press the timer to stop the beeping when the timer sounds.

5. After you press ENTER, the CHANNEL/FUNCTION display will change to CKL=REMOVE. Using the SCAN UP or SCAN DOWN arrows, Scroll to SIDE 2 Press ENTER to store the selection.

The function name (SIDE 2) will be displayed during the final countdown sequence.

6. To set the DUTY time press CHANNEL BUTTON 1 once. The CHANNEL/FUNCTION display will read, D1T=DUTY 1 TIME with up and down arrows. The current duty time for that channel will be displayed in the TIME display

7. Using the SCAN/UP Arrow or the SCAN/DOWN Arrow buttons, set the duty time at 3:00 minutes. Press the ENTER button to store the duty time. Note: The ENTER button must be pressed after any time changes in the cook, duty, or hold functions or the time change will not be stored.

8. Press the CHANNEL BUTTON 1 again; use the SCAN UP arrow or SCAN DOWN arrow to select MAN Cancel. Press the ENTER button to store your selection.

9. Press the CHANNEL BUTTON 1 again; use the SCAN UP arrow or SCAN DOWN arrow to select “TURN” from the list of function names. This name “TURN” will be displayed during the first part of the cook cycle, and when the duty time flashes and beeps. Press the ENTER button to store your selection.

10. Press the CHANNEL BUTTON 1 again; set the duty 2-time. Press ENTER.

Press the CHANNEL BUTTON 1 again; set the duty 3-time. Press ENTER.

Press the CHANNEL BUTTON 1 again, set the hold time. Press ENTER.

Press the CHANNEL BUTTON 1 again, set the hold alarm time. Press ENTER.

11. Press the CHANNEL BUTTONS 2-8 and complete steps 2 through 8 to program the remaining channels. (See page 5 for programming the “COOK” and “DUTY” times for these channels.)

12. Press the PRINCE CASTLE LOGO to exit programming mode.

Volume Adjustment

You can change the sound level of the alarm in RUN MODE. Press and hold the PRINCE CASTLE LOGO; then, within six seconds, press either the SCAN UP Arrow button or the SCAN DOWN Arrow button. The SCAN UP Arrow button adjusts the sound level to the louder alarm, and the SCAN DOWN Arrow button adjusts the sound level to the lower alarm.

Retrieved from "https://content.jacksvu.com/wiki2/index.php?title=Biscuit_Timer_Programming&oldid=750"